not applicable
Items 121 - 160 of 203
In stock
MK8 Teflon Nozzle made of brass CuZn37 for 1.75mm filament nozzle for 3D printer, type - MK8, coating - non-stick, material - brass CuZn37, filament diameter - 1.75mm, nozzle type - direct, nozzle length - 13mm, key width - 8mm, nozzle thread - M6, nozzle thread length - 4.9mm
In stock
Nozzle for Ideaformer IR3 3D printer, type - IR3, filament diameter - 1.75mm, nozzle type - Direct, nozzle length - 15mm, key width - 6mm, nozzle thread - M6, nozzle thread length - 7mm
In stock
V6 style teflon nozzle for 3D printer, type - V6 style, coating - non-stick, filament diameter - 1.75mm, nozzle type - direct, nozzle length - 13.2mm, shaft width - 7mm, nozzle thread - M6, nozzle thread length - 7.9mm
Best sellers
cured nozzle for interchangeable nozzles Hotend suitable for P1P / X1C
Best sellers
cured nozzle for interchangeable nozzles Hotend suitable for P1P / X1C
In stock
Throat Neck Screw CR10 Titanium Copper Neck Screw Throat M6*27.5mm 1.75mm Filament Heel Solid Metal The neck screw of your 3D printer ensures optimal heat dissipation from the heating block into the coldend? If your filament often "jams" in the throat, it may be because the processing and the thermal conductivity is not optimally matched to your printing process.
In stock
- Filament diameter 1.75 mm.
- Made of hardened steel.
- Suitable for thing:3016298.
- Suitable for Prusa i3 MK3
- Made of hardened steel.
- Suitable for thing:3016298.
- Suitable for Prusa i3 MK3
In stock
- Ball bearing mounted arm
- Adjustable spring tension
- Integrated filament guide
- Suitable for Nema 17 motors
- Can be used as direct or bowden setup
- Feeder wheel included
- M6 thread for PushFit or Throat available
- Colored anodized
- Adjustable spring tension
- Integrated filament guide
- Suitable for Nema 17 motors
- Can be used as direct or bowden setup
- Feeder wheel included
- M6 thread for PushFit or Throat available
- Colored anodized
In stock
Throat Neck Screw V6 Titanium Copper Neck Screw Throat M6 M7*22mm 1.75mm Filament Heel Solid Metal The neck screw of your 3D printer ensures optimal heat dissipation from the heating block into the coldend? If your filament often "jams" in the throat, it may be because the processing and thermal conductivity is not optimally matched to your printing process.
In stock
Throat Neck Screw V6 Titanium Copper Neck Screw Throat M6*21mm 1.75mm Filament Heel Solid Metal The neck screw of your 3D printer provides the optimal heat dissipation from the heating block into the coldend? If your filament often "jams" in the throat, it may be because the processing and the thermal conductivity is not optimally matched to your printing process.
In stock
Discover our fantastic heated bed clamps â the perfect addition to your 3D printer accessories! These little helpers will keep your print bed safe and stable while your masterpiece comes to life.
In stock
Made of high quality carbon steel for long life and better performance. For convenient connection of aluminum profiles and attachments.
In stock
Made of high quality carbon steel for long life and better performance. For convenient connection of aluminum profiles and attachments.
In stock
Made of high quality carbon steel for long life and better performance. For convenient connection of aluminum profiles and attachments.
In stock
Made of high quality carbon steel for long life and better performance. For convenient connection of aluminum profiles and attachments.
In stock
A small carbon steel filament drive with really sharp teeth. They are carefully manufactured on a synchronized CNC process that gives a sharp, even and cleanly cut tooth profile with incredibly good grip.
In stock
Silicone damper for heating bed - Height: 18 mm
This silicone damper for the heating bed of 3D printers increases stability, making bed leveling hardly necessary.
The existing springs are simply replaced by the silicone buffers.
Scope of delivery:
3 x silicone buffers 18mm length
1 x silicone buffer 16mm length
In stock
C20
3.2mm
HSS
10 pcs
3.2mm
HSS
10 pcs
In stock
This module allows you to automatically pause the 3D print job if the filament breaks or runs out. This allows you to insert new filament and resume the print job.
In stock
with compact handle with wear-resistant steel blade guide and blade magazine in the hollow handle,
- for blades with the code number "E" (shank-Ã 3,2 mm),
- for all tools with crank drive,
- for blades with the code number "E" (shank-Ã 3,2 mm),
- for all tools with crank drive,
In stock
This VolcanoV2 heater block allows you to use the high temperature PT100 sensors with high accuracy on your Volcano, making it compatible with the PT100 upgrade kit on your V6 hot end.
In stock
This sturdy corner angle made of steel connects three aluminum profiles at the same time at a right angle to each other. The aluminum profiles should have a cross-section of 20 mm x 20 mm and a groove opening of 6 mm.
In stock
Linear ball bearings or linear bearings for short, colloquially also called ball bushings or ball bushings, are special ball bearings with an unusual, because axial (instead of radial) ball circulation.
In stock
Inner diameter 8 mm, outer diameter 15 mm, length 45 mm, flange: 25 x 25 mm, silent running, LMK8LUU
In stock
DaVolcano Hot End Heater Block, Brass version for higher temperatures, Compatible with many printers, Easy to use, Only suitable for DaVulcano Nozzles, Filament diameter depends on Nozzle
In stock
Die and heating block for 1.75mm filament. The diameter is 0.4 mm.
In stock
This silicone dampener for the heating bed of 3D printers increases the stability, making bed leveling hardly necessary.
In stock
PTFE - 1.75mm - Natural - Operating temperature: 250°C - Max. temperature: 300°C - Melting point: 330°C - For Ultimaker 2, Ultimaker 2+, Extended
In stock
Throat for 3D printer, material - titanium Ti-5Al-2.5Sn, filament diameter - 1.75mm, length - 20mm, heel - with heel, heater block side - M6, cold end side - 6.9mm.
In stock
The neck screw of your 3D printer provides the optimal heat dissipation from the heating block into the coldend? If your filament often "jams" in the throat, it may be because the processing and thermal conductivity is not optimally matched to your printing process.
In stock
Fusing platform and air guide for Flashforge Creator Pro and similar printers such as MakerBot Replicator 2x
In stock
Inner diameter 10 mm, outer diameter 19 mm, length 55 mm, flange: 30 x 30 mm, quiet running, LMK10LUU
In stock
- Spring loaded - Integrated filament guide - Fits Nema 17 motors - Feeder wheel included - Semi-high design for replicator clones - Plastic
In stock
- Spring loaded - Integrated filament guide - Fits Nema 17 motors - Feeder wheel included - Semi-high design for replicator clones - Plastic
In stock
Advanc3D Ultimaker 2 Heat Sink (UM2 Aluminum Heat Sink -351707)
In stock
Advanc3D Heat Sink UM2 Mounting Bracket for Ultimaker 2
In stock
Advanc3D Cooler UM2 Mounting Bracket for Ultimaker 2
In stock
Inner diameter 8 mm, outer diameter 15 mm, length 25 mm, graphite inserts, self-lubricating, replacement for LM8UU, maintenance-free
In stock
- Spring tensioned
- Filament guide integrated
- Suitable for Nema 17 motors
- Feeder wheel included
- Semi-high design for replicator clones
- Colored anodized
- Filament guide integrated
- Suitable for Nema 17 motors
- Feeder wheel included
- Semi-high design for replicator clones
- Colored anodized
In stock
- Spring tensioned
- Filament guide integrated
- Suitable for Nema 17 motors
- Feeder wheel included
- Semi-high design for replicator clones
- Colored anodized
- Filament guide integrated
- Suitable for Nema 17 motors
- Feeder wheel included
- Semi-high design for replicator clones
- Colored anodized
Items 121 - 160 of 203